How to make a paper airplane? 13 schemes for folding airplanes with your own hands so that they fly far and high up to 10,000 thousand – About paper .net

Simple origami fighter for beginners

Prepare a sheet of A4 paper and follow the step-by-step instructions:

  1. Place the rectangle horizontally. Fold the upper side corners towards the middle.
  2. Fold the top corner down to the edge of the top layer.
  3. Align the right corner with the central fold.
  4. Repeat on the left side.
  5. Turn the workpiece over. Fold the lower right corner towards the center.
  6. Repeat with the left corner.

    How to make a paper airplane? 13 schemes for folding airplanes with your own hands so that they fly far and high up to 10,000 thousand - About paper .net

  7. Fold the top right side towards the center.
  8. Repeat with the left side.
  9. Fold the workpiece into a mountain.
  10. Bend one wing to the side.
  11. Then the second.
  12. Raise the corners at the bottom in the middle vertically.

    How to make a paper airplane? 13 schemes for folding airplanes with your own hands so that they fly far and high up to 10,000 thousand - About paper .net

  13. The fighter is ready.

The more complex and realistic the airplane model, the worse it flies. Simple fighters are aerodynamic and lightweight, so they can fly far and for a long time.

Did it work?

YesNo

How to launch a plane correctly so that it easily and simply flies 100 meters

In order for the airplane to fly long and beautifully, as well as over a long distance, it is important not only to follow the instructions and all the steps when creating it. The maneuverability of the model depends on the correctness of the lines and bends. But there are other, no less important nuances. So, if it is not possible to run the model outdoors, it is better to do it indoors with high ceilings.

Запуск
Alternatively, you can launch the plane from the balcony, but in this case you can say goodbye to your creation, because the air flow will probably pick it up and carry it far away.

In addition, a lot depends on the throwing technique. It is better to move away from the classical scheme, where the model is launched forward in a horizontal plane. You need to concentrate well and… try as hard as possible to throw the airplane up at an angle of 90 degrees.

If everything is done correctly and there is no strong wind, the flight altitude can be up to 5, or even higher, meters. After which the plane should independently assume a horizontal position and continue to hover smoothly. About 20 seconds can pass from the moment of the throw to the start of the fall.

1st place – paper airplane diagram “falcon”

This is probably one of the most beautiful paper airplanes that you can make with your own hands, because it is very similar to the real one. To fold such a long-flying airplane with your own hands, follow the detailed instructions with photos and videos at the end.

1 – take a sheet of medium-weight A4 paper and fold the sheet in half to make a paper airplane.

2 – fold a sheet of paper in half for the longest-flying paper airplane.

3 – fold the paper along the edges to make a cool airplane with your own hands.

4 – we also fold the second side of an airplane made from a sheet of paper.

5 – iron the resulting corners of the paper plane in half again.

6 – open each wing of the plane and turn them around.

7 – the photo below shows how to make the wings of a long-flying airplane out of paper for 100 meters.

8 – wrap both corners of the future paper airplane in different directions symmetrically.

9 – bend the outer part of the paper airplane to make it look like in the photo.

10 – on the back side of the airplane paper blank we make the same folds.

11 – next you need to open both parts of the resulting airplane wings.

12 – fold the paper plane to the isosceles angle of the triangle.

13 – along the fold line we roll up the paper airplane structure.

14 – then you need to bend the wings on both sides and align them symmetrically.

15 – follow the same steps according to the instructions for the remaining wings of the paper airplane.

https://www.youtube.com/watch?v=13yHFYhNQeM

16 – fold the second wing of the paper airplane.

17 – The next step is to fold the wings upward to improve the maneuverability of the paper airplane.

18 – bend the wings up for better stability of the paper airplane.

19 – on the other side we bend the corners on the wings.

20 – the flaps of a finished paper airplane can be bent so that it can fly further than 100 meters.

21 – if your paper plane crashes frequently and its nose becomes bent, fix it with nail polish.

The longest flying aircraft is ready for testing. If you launch it from the 9th floor or higher, it will fly and glide much further than the 100-meter mark. Gusts of wind and rising air currents will help the paper plane rise as high as possible and fly further.

Below is another interesting video on how to assemble a cool airplane similar to the F-15 in origami style. The diagram is complex, so watch carefully.

2nd place – diagram of an airplane made from paper “thunderstorm”

Let’s continue assembling a paper airplane that will fly for a long time according to a highly complex assembly scheme. We will need, as always, a sheet of A4 paper. This can be plain white or colored paper. You can also take sheets from magazines with medium paper thickness.

The first step is to bend the sheet in half. We remind you that depending on how smoothly and symmetrically your plane is assembled, it will fly in exactly the same way. After bending the sheet in half, unbend it and then move on to the second step.

The second step is to bend the corners to the center – on one side and the other. It turns out to be such a preparation.

Third step. The edges of the paper that formed an obtuse angle on the left are correctly bent again along the line of the nose of the aircraft to the right corners of the paper blank. See how it looks in the photo. Straighten the folds of the paper near the nose especially carefully so that everything is symmetrical.

Fourth step. We see a point at the intersection of the bends of the left and right edges of the workpiece. Along the line through this point you need to fold the airplane in half, as shown in the photo. You can check yourself by matching the lines of the central fold. After bending, unbend, turn over and bend in the opposite direction.

Fifth step. Turn the plane over again and fold the sides on the left and right towards the edge of the inner sheet. See photos and videos for more details.

After this, turn the plane over again and bend the nose forward again.

Turn it over again and turn the strip of folded paper towards the tail of the airplane blank.

Sixth step. We bend the plane along the central longitudinal axis. It is convenient to bend the stabilizers on the wings in this position parallel to one and the other side.

Seventh step. We bend the wings to the base. Here you can bend it in different ways and experiment, but it is considered optimal to bend it from the nose to the fender liner.

Everything should fit together smoothly and be symmetrical. Then the paper plane will fly exactly 100 meters or more and not lean left or right.

If the plane is flying downwards, then you need to bend the back of the wings slightly upward. Thus, the flow of oncoming air will lower the tail of the aircraft and raise the nose up.

See below for a detailed video with comments from the author on assembling such a long-flying paper airplane.

3rd place – diagram of an airplane made from paper “hawk”

Now we will assemble another complex aircraft.

First step. Fold the sheet in half exactly in the middle. The quality of the flight will depend on the evenness of the folds. All stages of the aircraft are done in a mirror manner – left and right.

Second step. We bend the left and right sides towards the center.

Third step – once again take the left and right edges of the paper and bend them towards the central axis of the plane.

The fourth step is to bend the sharp end of the workpiece towards the tail. In this case, the bend line of the sheet should pass through the point of intersection of the edges in the middle of the paper craft. Centering is checked by matching the central bend along the long side of the sheet.

Fifth step. We bend the edges of the paper on the left and right again towards the center, as in the photo. It is important here that the inner layer of paper does not bend or form wrinkles.

Sixth step. We grab the outer fold and open it, and then wrap it inward as shown in the photo. We do the same from the other side of the plane. We take the formed pockets and bend them inside out.

https://www.youtube.com/channel/UC1aJD7nhzF-XepgCCsWEqRQ

Seventh step. The pointed nose needs to be bent in the opposite direction about 1 cm deeper than the logical fold line. Pockets are formed there, which we bend inside the nose from approximately the middle.

Step eight. We also wrap the tip opposite the sharp nose.

Ninth step. We bend the paper airplane wings parallel to the keel. If the wings of your paper craft match, then the base of the airplane is assembled symmetrically.

Tenth step. We bend the edges of the wings parallel to the main axis of symmetry to form flaps. The plane is ready.

A detailed video on how to assemble such an airplane with your own hands from paper is given below.

4th place – paper plane “albatross”

Bend a sheet of A4 paper in half and draw it with your fingernail so that the fold is perfect.

We bend the edges of the paper inward towards the central axis.

After this, we bend the edges at an obtuse angle again towards the center. The edges of the paper should lie symmetrically on the central axis of our craft.

Then we bend the nose of the paper airplane towards the tail and align the centers of symmetry.

Add corner folds so that the left side is parallel to the right side.

We bend it back and bend the sharp nose of the plane back along the flight path. We iron all the seams with our nails.

We bend the wings so that a large area of ​​the wings remains load-bearing. We do everything extremely symmetrically so that the plane can fly further.

At the end we form the tail. In principle, the bend of the tail can be done as in the photo of any size.

We straighten the resulting folds upward so that it ends up in the space between the wings.

We bend the vertical stabilizers upward parallel to the main axis of symmetry of the paper airplane. This is the plane we have – try to fly it quickly.

If you still have any questions about assembling this aircraft, then watch the detailed video with comments.

5th place – the simplest paper airplane models

In this place are located all the simple models of airplanes that even a child can assemble and which we all assembled in class and let the girls and teachers see. For such tasks, ordinary blunt-nosed airplanes and gliders are quite suitable. Here are 10 of the best easy-to-assemble paper airplanes.

This is the simplest and most popular paper airplane – almost all people know it because they have been collecting it since childhood.

The following airplane model has a fast and smooth flight. Due to the front supporting wings, the nose does not collapse, providing stabilization, lift and long flight.

Next, let’s try to assemble a paper airplane with large wings – the design is simple and reliable.

Next will be a blunt-nosed aircraft with increased collision resistance.

The fifth one will be assembling a modified plane with a blunt nose. The circuit is simple, but requires careful assembly.

Now I propose to build a good airplane out of paper with nose wings and vertical rear stabilizers. The shape of the wing of such a glider allows you to fly longer in a straight line.

The next plane has a sharp nose and flies rapidly forward. The fins on the wings stabilize and prolong the flight of such a paper fighter.

The following scheme has good piercing abilities – the craft looks like a space fighter. It seems that it was created to exterminate enemy personnel.

The largest wings are those of the glider, which has a rather ridiculous appearance. But this does not prevent him from flying very long and far.

The amazing design of this airplane makes it look like a space shuttle or a Boeing. He flies not far, but effectively.

Paper airplanes for children

There are many toys that children love to play with. But there is one toy that has been around for many years and always wins the hearts of children, of course it is paper airplanes! They’re easy to make, they can fly, and they’re a lot of fun!

When a child makes a paper airplane with his own hands, the goal is to make it fly better, faster and higher. Children at school have competitions, they have to try different methods of making them, try new shapes and come up with their own original designs, painting them in all sorts of colors. Here are presented only four collages of the simplest models.

Paper airplane arrow. It’s a classic design that’s super easy to fold and a great option for beginners.

бумажный самолетик своими руками

Sea Glider


. The model simulates the flight of a seagull. Of course, it is a more complex airplane than the first one, but it flies better. бумажный самолетик своими руками

Humming airplane


. This model is ideal for long flights, and on the fly it makes a buzzing sound, like a fly flying. бумажный самолетик своими руками

Paper airplane fighter


. Compared to previous options, making such a paper airplane is much more difficult. But this is the fastest model, which makes it one of the favorites among children.

Important rules for making any paper airplane model

The first thing that can affect the distance an airplane flies is its shape. So, the product should be narrow and long, and the center of gravity should be concentrated in the bow. And, of course, it is important to choose the right model so that it is not just beautiful, but also capable of covering long distances in the shortest possible time.

Бумажный самолетик
Also, the flight duration is directly affected by the configuration of the wings.

When making a particular model, it is important to maintain balance and take into account the possibility of maneuverability in the air. When creating gliders, you must adhere to simple, but at the same time very important rules:

  1. Be careful when working with paper. It is important that it is even and smooth, without unnecessary folds, because the main characteristics of the finished airplane will depend on the integrity and smoothness of the sheet.
  2. Iron all folds well. This is necessary to keep the shape as best as possible.
  3. Correctly place the center of gravity.

    Построение
    To determine it, you need to know the ultimate goal and what to expect from the aircraft.

  4. Make folds on the wings. These should be the most “correct” places, because this determines how far and how long the glider will fly.
  5. Maintain symmetry. Perhaps this is the most important condition when creating a model. It completely influences the success of the build. At the same time, symmetry must be observed in everything, present in all details – wings, body, tail, etc.

In addition, it is worth mentioning the safety measures that must be observed during work, especially if small children are involved in the process. Use scissors carefully, and do not forget that you can cut yourself even with an ordinary sheet of paper.

Video bonuses

Do you want to get a plane that can not only take off high, but also return back to your hands? Do you think this can’t happen? But you are wrong.

Tireless experimental craftsmen have developed a design for an amazing boomerang aircraft.

With it, you can show your friends a stunning trick: a launched airplane will obediently fall right into your hands every time. To become known as the master of paper airplanes, check out this video – you will definitely succeed.

It would seem that all the paper airplane samples have already been reviewed and tested in practice, but we still have something to surprise you with. We invite you to watch a video lesson on creating a realistic glider plane.

You don’t even need origami folding skills, you just cut out the outline from paper. This model has excellent flight characteristics, and the whole secret lies in… ordinary plasticine. Watch the video, be surprised and amazed.

Creating various paper airplanes is not only a wonderful activity that allows you to drive away boredom and put away the ubiquitous gadgets. It develops intelligence, accuracy and fine motor skills. That is why it is so useful to include this type of activity in the program of joint leisure with children.

Perhaps the first unsightly model will be your child’s first step towards a serious interest in aircraft modeling. And it is in your family that a brilliant designer of passenger airliners or new jet fighters will grow up. Anything is possible. There is no point in looking too far into the future, but devoting an hour or two to folding paper airplanes is definitely worth it.

Perfect paper airplane

идеальный бумажный самолетик

As children, we all knew how to make paper airplanes and probably often wondered how to make the “perfect” paper airplane

. Well, not very complicated, but not like everyone else’s. This airplane has a different nose shape and will be close to perfect if each step is followed carefully and accurately.

To make the perfect paper airplane, you’ll need three things.

  1. One sheet of paper measuring 20 x 30 cm in any color.
  2. Any flat surface large enough to work on.
  3. And finally, the ingenuity and courage to accept possible failure after the first attempt.

This is not a normal plane, so it will require more steps than usual. Remember that patience is the key to success! The instructions, which you can read on the website, consist of 14 steps; below, see the master class with step-by-step photos.

Making a cardboard glider

The decision to make an airplane out of cardboard came with the purchase of furniture from IKEA.
Good and high quality packaging remains.

The decision has been made, I will move forward with this ancient project.
I start by making the ribs.

The main difficulty in cutting cardboard is its increased “garbage”, a lot of all sorts of abrasive. You have to constantly sharpen the cutter.

The first power ribs made of sanded plywood.

I make cardboard ones in composite parts. The simplest conductor.

And also a simple slipway for fixing the wing during assembly. There is no need to make a monumental system. I assume the model will be produced in one version.

The vertical walls of the side members are also made of cardboard. It works quite well for compression.

The power kit is almost ready, now the wingtips “ears”.

Servo wells are also made of cardboard. Reinforcing dialing and conducting wires to control.

Control weighing.

Then the wing skin. I mark the installation locations for the power frame, bend the trim around the forehead, and apply glue.

Then I mount the lower part of the sheathing. I lightly cut through the ailerons and servo well covers. Then I will make final cuts using these marks.

Tried on the wing connection tubes. Central aluminum 8mm, side carbon 6mm.

I cut off the ailerons and covered all the ribs with craft paper. To avoid warping of the structure, I fixed the ailerons until completely dry.

Hinged on plastic hinges.

Design deviations: up 30 degrees, down 80.

Finished wings.

I move on to the fuselage. The bow is made of sanded plywood. Consists of two parts. The main one, the wings and tail beams are attached to it. And the power one, which houses the motor, receiver, regulator, and battery. Structurally, they are connected by spikes. The idea is that with a strong impact, the bow part breaks, sacrificing itself. Keeping the entire structure intact.

The remains are then dismantled and a new version is made.
Fitting the side walls of the fuselage to the wing mount.

Half of the power section of the fuselage is ready without.

Side walls and bottom tail made of cardboard.

Strength frames with holes for bowdens.

I make tubes from ear sticks glued together with cyacrine.

I close the fuselage with the top cover and under the cargo.

Manufacturing of an all-rotating ruder.

Power frames made of plywood. Vertical, carbon tube.

Attaching the structure to the fuselage.

Manufacturing of an all-rotating elevator.

The installation rocker was redone several times.

This version of the boat is final.

Power units and mounting lugs to the boat in the elevator.

Finally the tail unit is ready.

I immediately check how everything is moving.

Almost finished plein air, turn behind the sacrificial front part of the fuselage.

Assembled the equipment and determined the length of the spout based on the position of the CG.

Docking and installing equipment, I happily realized I was in the center of gravity!

Now settings and flight.

Control weighing.

Before the flights, I painted the entire airframe with diluted TITAN glue.

First flight…

And of course my favorite activity….

I made a video of the operation of the wing, ailerons, ruder, and elevator. Everything is normal, cardboard structures do not flutter.

The time has come for finer settings, adjustments to the center of gravity, brakes, and control modes.

Some video from the board.

Of course, this is not a pure “match superliner”, but it flies quite well.

Participated with him in an air show. Indicatively, competitive flights.

I started with a DVR, I really wanted to make a video.

Of course, it significantly worsens the flow, and adds a fair amount of turbulence to the tail.

To my joy, I took third place of honor. This is against the backdrop of match superliners!

This is how “CARDBOARD” turned out.

P.S.
The screensaver shows a glider with one wing, the second one was recently broken at the opening of the season.
I’m renovating.

How to make a paper glider

как сделать планер из бумаги

Paper planner

It’s not difficult to do it yourself if you have a plan.

Of course, this model can be called rather a mini-glider
, but you can make your own glider of any size using the same proportions. In this case, the structure is 5 cm long with a wingspan of 8 cm.

To work you will need:

как сделать планер из бумаги

First draw a diagram
as shown in the photo. Cut out the model according to the drawn plan and fold it exactly in half. Use glue. Then fold the wings. Roll the sock around the fuselage and your paper glider is ready. Just keep in mind that this glider is very sensitive to even light winds
.

Remember two rules:

  1. The wing should not be in the center of the fuselage, but slightly closer to the nose.
  2. The area of ​​paper used on side “A” should be equal to side “B”. This can be done by first measuring the area of ​​side “A” and then adjusting the length of “X” so that the area of ​​”B” is the same as “A”.

How to make a boomerang airplane

There are several different styles of paper airplanes with a boomerang effect. Some models fly vertically in a circle, while others fly in a traditional horizontal pattern. It’s all a lot of fun for kids, although there are some tricks.

The first, a child-friendly design, has just a few folds and relies on adjusting the flaps to allow the airplane to return.

как сделать самолетик-бумеранг

How to fold a paper airplane is shown in the diagrams. True, the inscriptions are in English, but everything is simple there. Fold
– fold, tail
– tail, flap
– leaf, corner
– corner, envelope
– envelope.

The second, an origami airplane design, also has some folds, but flies back vertically rather than horizontally.

как сделать самолетик-бумеранг

To make the airplane, you will need one square sheet of origami paper. See the diagram below. как сделать самолетик-бумеранг

Third, more advanced aircraft

, consists of many tricky folds, but the result is an excitingly fun paper toy, even if the airplane is not folded perfectly. How to do this is shown in the diagram, but if you have no experience in origami, there may be some points in the photo that are not entirely clear. Therefore, it is better to read the instructions on the website
, each step is described there in more or less detail. Once folded, throw the plane away from you and watch it glide in a perfect, beautiful circle straight towards you! It’s very beautiful, it’s worth trying for it.

How to glue an airplane out of paper

как склеить из бумаги самолет

Anyone who likes miniature paper airplanes

, you will definitely like this model too. First you will need to draw and cut out the details, as shown in the photo below. Once this is done, start making the wings and horizontal stabilizer. Making wings should begin by drawing a line with a slope
. Along the leading edge, at the point where the wing thickness reaches 3 squares, make a horizontal line that extends 1.5 squares inward. Then join the edges. To make a horizontal stabilizer, mark 3 squares that have at least 1 square behind them. The slope of the leading edge should be 3/2 and the trailing edge should be 3/1. как склеить из бумаги самолет

как склеить из бумаги самолет

Solid lines
the diagram shows where to cut, dotted
indicate fold lines. Fold the rear fuselage in half along the dotted vertical line through this area. Once folded, make a cut along the thick line half a box above the bottom of the fuselage. Turn the steering wheel. Then secure the aircraft at the front, spars, counterweight and against the rudder. This is short, full instructions can be read on the website
.

Some facts from history

The first mention of the use of paper to create flying toys dates back to the first century AD. Of course, this was China with its luxurious paper kites. But the modern airplane did not appear until 1930. One of the founders of the Lockheed corporation, Jack Northrop, came up with the idea of ​​​​making paper copies of airplanes so that they could test design solutions in real airplanes being designed.

From the design office, the idea spread around the world much faster than real airplanes. Boys and girls shared ideas on how to make a paper airplane and launched their creations into the sky.

How to make a paper airplane? 13 schemes for folding airplanes with your own hands so that they fly far and high up to 10,000 thousand - About paper .net


The modern airplane did not appear until 1930

The Paper Aircraft Association was later founded by Andy Chipling. Moreover, in 2006, the Association held the first world championship, where fans competed in launching paper models. Today such championships are held regularly. They compete in three disciplines: flight range, gliding duration and figure aerobatics (aerobatics). There are also commercial tournaments, the most popular being Red Bull Paper Wings.

Note! The most desperate battle in this sport is over flight time.

Designers are constantly experimenting with designs and materials, trying to create models that fly for a very long time. The record of Ken Blackburn, whose plane stayed in the air indoors for 27.6 seconds, stood for thirteen years. This fact is recorded in the Guinness Book of Records.

Such an airplane belongs to the class of gliders. Moreover, the Blackburn model was created contrary to the opinion that models made of lightweight materials fly longer. The designer calculated that only a powerful starting throw, almost vertical, with a deviation of no more than ten degrees, could provide sufficient duration.

For longer flights or figure aerobatics, the models require a fundamentally different scheme. There are many well-known techniques for folding airplanes. They are constantly modified, supplemented and improved. After all, truly passionate creators do not want their creation to ingloriously bury its nose in the ground immediately after the start.

Volumetric cardboard craft

Let’s move on and make a toy out of an ordinary matchbox; it will be voluminous and cute. This is a rather interesting bioplane that will delight anyone; it can be given as a souvenir for the holiday on February 23 or May 9.

We will need:

  • cardboard – 2 sheets
  • PVA glue
  • ruler
  • pencil
  • scissors
  • matchbox

Work steps:

1. Mark two strips on the cardboard with a pencil; their width should be equal to a matchbox.

2. Then use scissors to cut them out. Use these strips to make airplane wings. On another sheet, mark two 1.5 cm wide strips and also cut them to the length of the cardboard.

Move one such thin strip, and cut the second into two parts of 8 cm, remove the rest, it will not be needed. Here’s what you get:

3. Now start assembling. Take a matchbox, bend a long thin strip in half and attach it, glue it to the box.

4. Using two identical strips that are wide like boxes, make wings.

The corners can be rounded; cut them with scissors.

5. Make a tail from one short narrow strip and also round it, glue it inside. And glue the second one on top, make a triangle out of it.

6. Then you can cut out the propeller and glue it.

7. The craft is ready, enjoy your work!

Origami paper airplane

оригами самолетик из бумаги

In principle, this model is familiar to many, we can say that this paper airplane

is a traditional model. It is quite durable, easy to assemble, and flies long distances. оригами самолетик из бумаги

This model has many names: “rocket”, “arrow”, dart”, “spear”, well, everything like that. This comes from the fact that the model flies just like a rocket or a thrown spear. One thing to know, you will need a piece of A4 paper
, or any other rectangular shape. Below you can see diagrams on how to fold this paper airplane with your own hands

. Although everything is quite simple, to be sure, you can also read the step-by-step instructions on the website.

Step-by-step scheme for manufacturing a fighter

Fold a sheet of paper in half lengthwise.

Бумага

Expand. The bend, which is clearly visible, will be a guide.

Загиб

Fold one corner of the paper towards the middle.

Угол

Do the same with the second one.

Голова самолета

Next, bend the corner again, it will turn out sharp and long. Do the same manipulations with the second one.

Уголки

Fold edge to edge, point to opposite side. At this stage, it is worth making sure that the tip is located strictly in the center.

Острие

After this, fold it in half with a sharp triangle facing outwards, as shown in the photo.

Построение

Tuck in the corner, being careful.

Заворот

Also the opposite.

Углы

Unfold the workpiece, while the corners that are turned should remain untouched.

Заготовка

Unscrew the tip back, taking into account the corners that are under it.

Острие

Fold this gap in half.

Сгибание пополам

Make wings, first one. Then the second.

Крылья

The easiest way is a reconnaissance aircraft or Tu-123

First, you need to mark the middle on a sheet of paper (rectangular), then make a contour marking along which parts of the sheet are carefully folded. After this, the leaf is folded in half lengthwise, and the necessary bends are made on it, as shown in the photo.

Оригами

Small folds are noted on the resulting figure, after which the right corner is tucked inward, as shown in the photo. A straight dotted line is drawn along the bottom of the body, and the wings are folded along it.

Крылья

Assembling a paper airplane

Assembly. Between the halves of the wing (Fig. 13) we place one or two gaskets with the fold upward. From the front, the gasket should be visible 30-35 mm. We insert both ends of the wing together into the front slot of the fuselage, from below, from the inside. Pull them up so that the gasket fits tightly along the fold of the fuselage.

With the wing in place, use the sharp end of a pair of scissors to poke holes in two places through the fuselage, gasket and wing. Insert one pin into the punctures. The pin is inserted only on the side from which the puncture is made. Having tightened the pins as tightly as possible, bend their ends and cut them short.

Now that the wing is secured, let’s move on to assembling the tail section of the model. We will insert the stabilizer into the prepared hole in the fuselage in the same way as the wing. Before securing it, install the keel with the fold forward. Then we will make two punctures through the fuselage, the base of the stabilizer, the fin and the gasket.

Now let’s assemble the forward part of the fuselage. Fold both strips of weight in four. Then we unfold the load and begin to fold it from the edges inward (Fig. 14). Iron the finished load along the folds with the edge of the scissors so that it does not open. We will place the cargo inside the forward part of the fuselage.

The end of it should reach the wing. Let’s straighten the cargo so that it does not protrude from the fuselage below, and make two punctures through the fuselage and the cargo. It is difficult to get a puncture without the habit. You need to press firmly with the end of the scissors and, slowly, slightly swing the scissors until their end comes out on the other side by 10-15 mm. Insert pins into the punctures. Cut off the end of the weight protruding from the forward part of the fuselage.

    Only now that the wing and tail section are installed and the cargo is secured can the wing and stabilizer be folded back.

     Fold the wing flush with the top edge of the fuselage (this is the wing installation line). The stabilizer is the same as the wing.

     The wing of the model, until the spar is inserted into it, is fragile, it is not yet capable of supporting the model in flight. Therefore, we will make a spar.

     Fold the strip of paper intended for the spar eight times. The folds should be as small as possible. We cut off the rest of the paper and sharpen the ends of the workpiece. Let’s smooth the spar with scissors so that it is thinner and does not unravel.

To install the spar, we will make punctures on the wing 10-15 mm from its leading edge (Fig. 15). First, insert the spar into one slot, then use the sharp end of the scissors to push it into the other. We’ll make two punctures behind the spar. Let’s insert the pins into them. To avoid cutting through the thin wing with the pins, we will press the puncture areas with our fingers.

Now carefully iron the wing with our fingers to eliminate distortions and bends.

Before launching the paper airplane, let’s first check the alignment. The center of gravity of the model should be on the front third of the wing (Fig. 16). If you get a rear alignment, you need to increase the load. To do this, you will have to rivet the bow part and, adding two or three strips of paper, fasten it again.

Let’s also check the installation of the wing and tail of the aircraft. On a paper airplane, the glider is given – technically speaking – a zero angle of attack. This means that the plane of the wing has no inclination either up or down. The stabilizer of the training glider model has a negative angle of attack, approximately 2°, that is, its trailing edge should be slightly higher than the leading edge.

When launching, the paper airplane should be held over the shoulder with two fingers under the wing by the fuselage and directed horizontally, lowering the nose of the model slightly. We will launch the paper model not with a jerk, but with a strong but smooth movement. A push that is too sharp will cause the model to fly up and then dive, while a weak push will not give the required speed and the model will not fly far. Under no circumstances let the model go up; this will not achieve smooth and long-term planning.

A correctly made model should fly through the room at the same height. In a school hall or corridor, a well-adjusted model flies with a descent of 20-25 m.

Su-35

Such an aircraft is capable of fulfilling several goals at once. Moreover, it is an extremely maneuverable bomber. Refers to fourth generation fighters. The diagram shows in detail how to build such an airplane from simple paper.

СУ-35
The clip on the nose is needed to make it heavier, then the plane will fly smoothly, and not take off sharply and immediately fall.

Scheme for creating a paper bomb truck

Using this aircraft, pilots dropped bombs behind enemy lines. It is not surprising that boys prefer to play “war” with this airplane. Making a model is not at all difficult, the main thing is to follow the instructions. First, you need to fold the sheet so that you get a triangle on top.

Next, you will have to find the center where the diagonals intersect and bend the paper along this central point. If everything is done correctly, triangles should appear in the side parts, with a center line outlined. They need to be bent to the inside.

Бомбовоз

Lightly mark a vertical line in the middle, then parallel to the base of the triangle. After this, the template is turned over and the corner is folded towards itself.

Шаблон

It is important to remember to fold the workpiece in half along the top. Next, you need to turn the future airplane over again and turn the corners up. There will be little left – just a few movements, as shown in the photo, and the real bomb truck is ready.

Заготовка

Circuits that provide fast flight

Do you want to take part in an aircraft model competition? They are easy to arrange at home. Just make high-speed airplanes out of paper and you can set your own records.

Be sure to check out the video master class on creating fast paper airplanes to avoid annoying mistakes and learn from the experience of others.

Step-by-step following our photo instructions is the key to success. A number of general recommendations will also help beginning paper aviation enthusiasts.

  1. To improve flight performance, use only a completely flat sheet of paper. Ideal for regular office printers. Any bruises and folds will repeatedly worsen the aerodynamic properties of the model.
  2. Iron all folds with a ruler to make them clearer.
  3. The sharp nose of the plane increases its speed
    , but at the same time the range decreases
    flight.

Ready-made crafts can be painted with the children. This exciting activity will allow you to turn a folded piece of paper into a real attack aircraft or an unusual fighter.

Approach creating your models like a science experiment. The speed and ease of assembling origami airplanes allows you to analyze their flight and make the necessary changes to the design.

What are the benefits of practicing origami

It is clear that many parents often have questions about the usefulness of origami classes. Is it really necessary to spend time on this, both yours and your child’s? Experts have long found out that origami classes are really useful. The child develops dexterity, perseverance, attentiveness, and concentration.

https://www.youtube.com/watch?v=bXK0Ihb8SNw

Spatial thinking is formed, which will be so useful to him in geometry and physics lessons, imagination develops, which will also have a beneficial effect on his studies. After all, no one is stopping a child who has already mastered several methods of making airplanes from coming up with some kind of his own model, slightly improving and modifying the old method.

Paper airplane models

Important! It would not be amiss to inform him that some paper models are capable of not only staying in the air for a long time, but also performing aerobatics. This will be an additional incentive, will interest the child and, perhaps, take him away from the computer for a long time.

Believe me, a plane made by the hands of your beloved child is a miracle in itself, especially for parents. How much pride your child will feel if this plane, which he built himself, will fly for a long time.